Renaissance Steel Security Gate 930mm Wide x 2000mm High

The Renaissance Steel Security Gate offers a wider fit and enhanced deadlock security, making it ideal for larger residential entrances and wider access points. Its adjustable hinge design provides flexible installation while maintaining practical everyday protection.
Designed for homes, rentals, and residential properties needing wider coverage than standard gates, Renaissance provides a practical security upgrade without the complexity of custom systems.
For larger or higher-risk sites, Xpanda recommends our custom welded security gates for maximum strength.

• Width: 910mm
• Height: 2000mm
• Mild steel, zinc plated + epoxy coated
• Type: Fixed swing gate
• Adjustable hinge fitting (Sill or face fix)*

*Size Clarification

When installed, final width can vary depending on hinge type and fixing method.

For masonry walls (sill-fixed hinges):

• Minimum installed width: 885mm
• Maximum installed width: 930mm

For wooden frames (face-fixed hinges):

• Minimum installed width: 865mm
• Maximum installed width: 910mm

• Wider Coverage:
  Designed to fit slightly larger openings than other gates in the range.
• Deadlock Security:
  Key-operated deadlock adds stronger protection for residential entry points.
• Adjustable Fit:
  Hinges allow installation inside or outside the door frame.
• Durable Finish:
  Coated steel finish designed to withstand everyday New Zealand conditions.

• Homes and larger entrances
• Apartments and townhouses
• Rental properties
• Utility access points
• Holiday homes and baches

• Renaissance gate panel (steel, coated finish)
• Deadlock with keys
• Adjustable Hinges
• Lock Protection Plate
• Lock Keep
• Fixings
• Instruction guide 

How to Install a Renaissance Security Gate

The Renaissance Security Gate is designed for straightforward installation using common DIY tools. Follow the steps below to ensure a secure fit and smooth operation.

🛠️ Tools Required

🖊️ Marker or pencil
📏 Measuring tape
📐 Spirit level
🛠️ Multi-purpose drill
🔩 Drill bits (2mm, 4mm, 6mm, 8mm, 10mm for steel or timber)
🧱 Masonry drill bits (6mm and 10mm)
🔧 Phillips and flat-head screwdrivers
🔧 10mm and 13mm ring spanners

Step 1. Measure the Door Frame Width

Measure the inside width of the doorway where the gate will be installed. Always measure from inside the frame to ensure the gate fits correctly.

🚪 Measure carefully before proceeding.

Step 2. Attach the Hinges to the Gate

a. Attach the hinges to the gate.

b. Do not fully tighten them yet—leave enough movement for adjustment.

c. Align the hinges with the door frame.

Step 3. Position the Lock-Keep and Hinges

a. Centre the lock-keep over the lock tongue.

b. Use adhesive tape to temporarily hold the lock-keep in place.

c. Leave approximately 5mm clearance between the lock and lock-keep.

d. Connect the top, middle, and bottom hinge sections.

e. Secure them temporarily with tape.

Step 4. Position the Gate in the Doorway

Place the gate into the door frame.

• 🧱 Masonry installation: position the gate parallel to the frame.
• 🪵 Timber installation: position the gate perpendicular to the frame.

Step 5. Adjust the Gate Position

Adjust the female hinge bolts to widen or reduce the gate reach until the desired position is achieved.

• 📏 Masonry fitment range: 885mm–930mm
• 📏 Timber fitment range: 865mm–910mm

Step 6. Tighten Hinges and Check Alignment

a. Tighten all female hinge bolts.

b. Use a spirit level to confirm the gate is straight.

c. Mark the top, middle, and bottom hinge positions.

d. Carefully remove the gate.

Step 7. Secure the Hinges to the Frame

a. Drill holes at the marked hinge locations.

b. Insert and tighten the supplied hex bolts.

c. Ensure all fixings are securely fastened.

Step 8. Install the Lock-Keep

a. Leave the lock-keep temporarily attached to the gate.

b. Close the gate and mark the lock-keep position.

c. Remove the gate and lock-keep.

d. Drill the marked holes and secure the lock-keep.

Step 9. Check the Lock Tongue Direction

The angled side of the lock tongue must face the direction the gate closes.

⚠️ If installed incorrectly, the gate may not latch properly.

Step 10. Adjust the Lock Cylinder

If required, adjust the lock tongue direction to suit your installation.

a. Remove the lock cylinder from the gate.
b. Turn the key approximately 10° until the centre bar is flush.
c. Insert the cylinder into the lock body.
d. Extend the tongue until the retaining screw becomes visible.
e. Remove the retaining screw and withdraw the tongue.
f. Rotate the tongue to the correct orientation.
g. Reinsert the tongue and secure the retaining screw.
h. Reinstall the lock cylinder.
i. Confirm the tongue extends and retracts correctly.
j. Secure the lock using the supplied screws.

Step 11. Install the Lock Protection Plate

a. Centre the protection plate over the lock area.

b. Mark the fixing holes.

c. Drill the holes and secure the plate using the supplied screws.

Final Check

• ✔ Gate opens smoothly
• ✔ Gate closes correctly
• ✔ Lock engages securely
• ✔ Hinges are firmly attached
• ✔ Protection plate is installed

Your Renaissance Security Gate is now ready to provide an additional layer of security for your home, rental property, or business.